1] Scope – This specification covers seamless, straight-seam welded, and heavily cold worked Welded Austenitic Stainless Steel Pipe intended for high-temperature and general corrosive service.
When the impact test criterion for a low-temperature service would be 15 ft·lbf [20 j] energy absorption or 15 mils [0.38 mm] lateral expansion, some of the austenitic stainless steel grades covered by this specification are accepted by certain pressure vessel or piping codes without the necessity of making the actual test. For example, grades tp304, tp304l, are accepted by the ASME pressure vessel code, section viii division 1, and by the chemical plant and refinery piping code, ANSI b31.3, for service at temperatures as low as −425 °f [−250 °c] without qualification by impact tests. Other AISI stainless steel grades are usually accepted for service temperatures as low as −325 °f [−200 °c] without impact testing. Impact testing may, under certain circumstances, be required. For example, materials with chromium or nickel content outside the AISI ranges, and for material with carbon content exceeding 0.10 %, are required to be impact tested under the rules of ASME section viii division 1 when service temperatures are lower than −50 °f [−45 °c].
A312 TP 304/304l - are intended for service at temperatures where creep and stress rupture properties are important. Optional supplementary requirements are provided for pipe where a greater degree of testing is desired. These supplementary requirements call for additional tests to be made and, when desired, it is permitted to specify in the order one or more of these supplementary requirements.
These dimensions are also applicable to heavily cold worked pipe. Pipe having other dimensions is permitted to be ordered and furnished provided such pipe complies with all other requirements of this specification
The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “m” designation of this specification is specified in the order.
Note 2 — the dimensionless designator nps (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size"
2] Terminology – The definitions in specification A999/A999m and terminology A941 are applicable to this specification.
3] Ordering Information – Orders for material to this specification shall conform to the requirements of the current edition of specification a999/ a999m.
4] General Requirements – Material furnished under this specification shall conform to the applicable requirements of the current edition of specification a999/a999m unless otherwise provided herein.
5] Materials and Manufacture – The pipe shall be manufactured by one of the following processes: Seamless (sml) pipe shall be made by a process that does not involve welding at any stage of production.
6] Heat Treatment – All Pipe shall be furnished in the heat-treated condition in accordance with the requirements of table 2. Alternatively, for seamless pipe, immediately following hot forming while the temperature of the pipes is not less than the minimum solution treatment temperature specified in table 2, pipes shall be individually quenched in water or rapidly cooled by other means (direct quenched).
7] Product Analysis – At the request of the purchaser, an analysis of one billet or one length of flat-rolled stock from each heat, or two pipes from each lot shall be made by the manufacturer. A lot of pipe shall consist of the following number of lengths of the same size and wall thickness from any one heat of steel
What is SS 304 Grade - type 304 stainless steel is a t 300 series stainless steel austenitic. It has a minimum of 18% chromium and 8% nickel, combined with a maximum of 0.08% carbon. It is defined as a chromium-nickel austenitic alloy. Grade 304 is the standard "18/8" stainless that you will probably see in your pans and cookery tools.
What is ss 304 used for - 304 stainless steel is used for a variety of household and industrial applications such as food handling and processing equipment, screws, machinery parts, utensils, and car headers. 304 stainless steel is also used in the architectural field for exterior accents such as water and fire features.
Which is better SS 304 or SS 316 - since type 316 stainless steel alloy contains molybdenum bearing it has a greater resistance to chemical attack than 304. Type 316 is durable, easy-to-fabricate, clean, weld and finish. It is considerably more resistant to solutions of sulfuric acid, chlorides, bromides, iodides and fatty acids at high temperature.
Which is cheaper SS 304 or SS 316 - 304 stainless is also cheaper in cost compared to 316, another reason for its popularity and widespread use. Stainless 316 is more expensive because it provides a higher corrosion resistance, especially against chlorides and chlorinated solutions.
How is SS 304 pipe weight calculated - thick (mm) x w. Thick (mm) x 0.0248 = wt. What is the full form of erw pipe-electric resistance welded (erw) pipe is manufactured by cold forming a flat steel strip into a rounded tube and passing it through a series of forming rollers to obtain a longitudinal seam. The two edges are then simultaneously heated with a high frequency current and squeezed together to form a bond.
Why does stainless steel not rust - stainless steel is a steel alloy that contains a minimum chromium content of 10.5%. The chromium reacts with the oxygen in the air and forms a protective layer that makes stainless steel highly resistant to corrosion and rust.
Can stainless steel rust in salt water - stainless steel can, in fact, rust and corrode if continuously exposed to saltwater or other corrosive conditions over time. Grade 304, otherwise referred to as the uns 30400, is the most popular of austenitic or the 300 series. ... That's why this metal displays a higher resistance to corrosion by salty water.
nps designator; Under 2 2 to 5 6 and over |
Lengths of pipe in lot 400 or fraction 200 or fraction thereof 100 or fraction thereof |
The results of these analyses shall be reported to the purchaser or the purchaser’s representative, and shall conform to the requirements specified
If the analysis of one of the tests specified in 8.1 does not conform to the requirements specified in section 7, an analysis of each billet or pipe from the same heat or lot may be made, and all billets or pipe conforming to the requirements shall be accepted.
8] permitted variations in wall thickness - In addition to the implicit limitation of wall thickness for seamless pipe imposed by the limitation on weight in specification a999/a999m, the wall thickness for seamless and welded pipe at any point shall be within the tolerances specified in table 3, except that for welded pipe the weld area shall not be limited by the “over” tolerance.
The wall thickness and outside diameter for inspection for compliance with this requirement for pipe ordered by nps and schedule number is shown in table x1.1.
Annealing requirements |
|
Heat treatment |
1900 °f [1040 °c] |
Size | Sch | Price | Rate inr | Rate in riyal sar dihram | Random length | Shape |
¼’’ to ½’’ | Sch-5/5s/10/s10/40/40s/80/80s/160/160s/xxs and special thickness | $9589.04 per tons | 699997.0004 per tons | 197780 | 10 feet 5-6 mtr 10-12 mtr | Round U shape L shape Boiler shape |
¾’’ to 2’’ | Sch-5/5s/10/s10/40/40s/80/80s/160/160s/xxs and special thickness | $7500 | 54750004 per tons | 150000 | 10 feet 5-6 mtr 10-12 mtr | Round U shape L shape Boiler shape |
2 ½’’ to 10’’ | Sch-5/5s/10/s10/40/40s/80/80s/160/160s/xxs and special thickness | $6500.00 | 47450004 per tons | 130000 | 10 feet 5-6 mtr 10-12 mtr | Round U shape L shape Boiler shape |
12’’ to 24 | Sch-5/5s/10/s10/40/40s/80/80s/160/160s/xxs and special thickness | $7850.00 | 57305004 per tons | 157000 | 10 feet 5-6 mtr 10-12 mtr | Round U shape L shape Boiler shape |
Colombia | Jordan | France | Nigeria | Chile | |
Cuba | Ghana | Kazakhstan | Germany | Norway | Yemen |
Indonesia | Greece | Kenya | Lebanon | Oman | |
United Kingdom | Grenada | Korea | Malaysia | Pakistan | Saudi Arabia |
Argentina | Hungary | Kuwait | Maldives | Panama | Singapore |
Australia | Iran | Israel | Lithuania | Bahrain | Tunisia |
Belgium | Iraq | Italy | Luxembourg | Bangladesh | Paraguay |
Brazil | India | Japan | Mauritius | Uzbekistan | Peru |
Canada | Algeria | Korea | Turkmenistan | Bulgaria | Poland |
Denmark | Zambia | Mexico | Turkey | Cambodia | Portugal |
Djibouti | Andorra | Netherlands | Somalia | Uruguay | Qatar |
Dominica | Angola | Philippines | South Africa | Nepal | Romania |
Egypt | Armenia | Spain | Sri Lanka | New Zealand | Uganda |
Albania | Austria | Sweden | Sudan | Tajikistan | Ukraine |
Bhutan | Azerbaijan | United states | Vietnam | Thailand | United Arab emirates |
ASME b 36.19m pipe, aisi 304l pipe | Sa312 tp 304l pipes with sch 40s | Annealed, seamless, cold finish | Ss astm a 312 gr 304l pipe | Coil form ss 304 pipe |
Sch 80 smls pipe sa312 304l | Sch-10 seamless pipe a312 tp 304/304l | Sch-xxs seamless pipe ss 304l | High pressure seamless pipe for gas | Seamles pipe for turbine |
Seamless pipe bevel end a312 tp 304/304l | Seamless pipe plain end a312 tp 304/304l | Threaded seamless pipe a312 tp 304/304l | Bright annealing tube a312 tp 304/304l | U shaper pipe seamless a312 tp 304/304l |
Jindal round pipe ss 304 | Steel manufacturing company astm a312 tp 304/304l | Stainless steel pipe stockiest dammam | Stainless steel pipe stockiest jubail | Stainless steel pipe stockiest sasui Arabia |
Ss 304 welded pipe manufacturer | Ss 304 welded pipe supplier | Ss 304 welded pipe exporter | Ss 304 welded pipe distributors | Ss 304 welded pipe Dealers |
Ss 304 welded pipe Stockiest | Electro polish ss 304 pipe stockist | A312 tp 304l pipe nipple | A312 tp 304l pipe fabricators | A312 tp 304l piping spool |
Astm a312 hollow pipe | A312 tp 304l bush pipe | A312 tp304l tapper pipe | A312 tp 304l furniture pipe | A312 tp 304best prices pipe |
A312 tp 304 pipe manufacturer in Mumbai | A312 tp 304 pipe manufacturer in gujrat | A312 tp 304l pipe sunblasting | Electro plasting ss 304 pipe | En series ss304 pipe manufacturer |
A312 pipe importer | A312 tp pipe deal in lot | A312 tp 304 pipe for oil gas | A312 tp 304 pipe for heat exchanger | A312 tp 304 pipe for boiler |
A312 tp 304 pipe for aerospeace | A312 tp 304 pipe for mining | A312 tp 304 pipe for cement | A312 tp 304 pipe for phosphoric acide | A312 tp 304 pipe for sulphric acid |
A312 tp 304 pipe for carbon | A312 tp 304 pipe for child water | A312 tp 304 pipe for hot water | A312 tp 304 pipe for dry place | A312 tp 304 pipe for oil place |
A312 tp 304 pipe for gas line | A312 tp 304 pipe for sugar plant | A312 tp 304 pipe for crude oil | A312 tp 304 pipe for energy | A312 tp 304 pipe nace approved |
A312 tp 304 pipe transfroer | A312 tp304 pipe for hydrotest | Electro fusion welded 304 pipe | Ssaw 304l pipe | |
Aisi 304/304l seamless pipe | Astm a358 efw pipe 304 | Aisi 240 tp/304/304l | Stainless stel 304 –sch-10 sch-40 sch-80 sch-160 sch-xss pipe | Ss 304 bare pipe |
Uns-30400 pipe | Schedule 5s astm a213 stainless steel 304 pipe | Schedule 40 tp304 ss pipes | Ss werkstoff nr. 1.4301 clad pipes | Sa213 tp304 cold drawn pipes |
Ss uns s30400 bush hex pipes | Ss werkstoff nr. 1.4301 beveled end pipes | Capillary 304 stainless steel thin pipes | Ss uns s30400 electropolished pipes | 304 stainless steel rectangle pipes |
Seamless & drawn ss 304 pipe | Process equipment ss 304 pipe | A269 tp304/304l boiler tube supplier manufacturer | A269 heat exchanger tube | A269 bright annealing tube |
1. A213 tp 304 boiler seamless tube | A213 tp 304 boiler pipes | A269 seamless tubular product | A213 tp 304 boiler seamless tube | A269 thermal power plant seamless tube and pipes |
A269 sugar plant pipe | A213 food grade tube | A213 tp 304/304l annealing tube | Din en 10028-7 grade pipe supplier | Din en 10028-7 grade tube supplier |
Din en 10028-7 grade seamless pipe supplier | Din en 10028-7 grade efw pipe supplier | Din en 10028-7 grade hollow section pipe supplier | Din en 10028-7 grade pipe fittings supplier | Din en 10028-7 grade pipe manufacturer |
The steel pipe data chart below can be used to find pipe sizes, diameters, wall thickness, working pressures and more. The chart is based on ASME/ANSI b 36.10 welded and seamless wrought steel pipe and ASME/ANSI b36.19 stainless steel pipe.
Regardless of schedule number, pipes of a particular size all have the same outside diameter (not withstanding manufacturing tolerances). As the schedule number increases, the wall thickness increases, And the actual bore is reduced.
For example:A 4 inches (100 mm) schedule 40 pipe has an outside diameter of 4.500 inches (114.30 mm), a wall thickness of 0.237 inches (6.02 mm), giving a bore of 4.026 inches (102.26 mm) a 4 inches (100 mm) schedule 80 pipe has an outside diameter of 4.500 inches ( 114.30 mm), a wall thickness of 0.337 inches (8.56 mm), giving a bore of 3.826 inches (97.18 mm)
Pipe size |
Outside diameter |
Identification |
Wall thickness - t - |
Inside diameter - d - |
Area of metal |
Transverse internal area |
Moment of inertia - - l - |
Weight pipe |
Weight |
External surface |
Elastic section modulus |
|||
(inches) |
(inches) |
Steel |
Stainless steel schedule no. |
(inches) |
(inches) |
(square inches) |
(inches4) |
(pounds per foot) |
Water (pounds per foot) |
(square feet per foot of pipe) |
(in3) |
|||
- a - (square inches) |
- a - (square feet) |
|||||||||||||
Iron pipe size |
Schedule No. |
|||||||||||||
1/8 |
0.405 |
. Std Xs |
. 40 80 |
10s 40s 80s |
.049 .068 .095 |
.307 .269 .215 |
.0548 .0720 .0925 |
.0740 .0568 .0364 |
.00051 .00040 .00025 |
.00088 .00106 .00122 |
.19 .24 .31 |
.032 .025 .016 |
.106 .106 .106 |
.00437 .00523 .00602 |
1/4 |
0.540 |
. Std Xs |
. 40 80 |
10s 40s 80s |
.065 .088 .119 |
.410 .364 .302 |
.0970 .1250 .1574 |
.1320 .1041 .0716 |
.00091 .00072 .00050 |
.00279 .00331 .00377 |
.33 .42 .54 |
.057 .045 .031 |
.141 .141 .141 |
.01032 .01227 .01395 |
3/8 |
0.675 |
. Std Xs |
. 40 80 |
10s 40s 80s |
.065 .091 .126 |
.545 .493 .423 |
.1246 .1670 .2173 |
.2333 .1910 .1405 |
.00162 .00133 .00098 |
.00586 .00729 .00862 |
.42 .57 .74 |
.101 .083 .061 |
.178 .178 .178 |
.01736 .02160 .02554 |
1/2 |
0.840 |
. . Std xs . Xxs |
. . 40 80 160 . |
5s 10s 40s 80s . . |
.065 .083 .109 .147 .187 .294 |
.710 .674 .622 .546 .466 .252 |
.1583 .1974 .2503 .3200 .3836 .5043 |
.3959 .3568 .3040 .2340 .1706 .050 |
.00275 .00248 .00211 .00163 .00118 .00035 |
.01197 .01431 .01709 .02008 .02212 .02424 |
.54 .67 .85 1.09 1.31 1.71 |
.172 .155 .132 .102 .074 .022 |
.220 .220 220 .220 220 .220 |
.02849 .03407 .04069 .04780 .05267 .05772 |
3/4 |
1.050 |
. . Std xs . Xxs |
. . 40 80 160 . |
5s 10s 40s 80s . . |
.065 .083 .113 .154 .219 .308 |
.920 .884 .824 .742 .612 .434 |
.2011 .2521 .3326 .4335 .5698 .7180 |
.6648 .6138 .5330 .4330 .2961 .148 |
.00462 .00426 .00371 .00300 .00206 .00103 |
.02450 .02969 .03704 .04479 .05269 .05792 |
.69 .86 1.13 1.47 1.94 2.44 |
.288 .266 .231 .188 .128 .064 |
.275 .275 .275 .275 .275 .275 |
.04667 .05655 .07055 .08531 .10036 .11032 |
1 |
1.315 |
. . Std xs . Xxs |
. . 40 80 160 . |
5s 10s 40s 80s . . |
.065 .109 .133 .179 .250 .358 |
1.185 1.097 1.049 .957 .815 .599 |
.2553 .4130 .4939 .6388 .8365 1.0760 |
1.1029 .9452 .8640 .7190 .5217 .282 |
.00766 .00656 .00600 .00499 .00362 .00196 |
.04999 .07569 .08734 .1056 .1251 .1405 |
.87 1.40 1.68 2.17 2.84 3.66 |
.478 .409 .375 .312 .230 .122 |
.344 .344 .344 .344 .344 .344 |
.07603 .11512 .1328 .1606 .1903 .2136 |
1 1/4 |
1.660 |
. . Std xs . Xxs |
. . 40 80 160 . |
5s 10s 40s 80s . . |
.065 .109 .140 .191 .250 .382 |
1.530 1.442 1.380 1.278 1.160 .896 |
.3257 .4717 .6685 .8815 1.1070 1.534 |
1.839 1.633 1.495 1.283 1.057 .630 |
.01277 .01134 .01040 .00891 .00734 .00438 |
.1038 .1605 .1947 .2418 .2839 .3411 |
1.11 1.81 2.27 3.00 3.76 5.21 |
.797 .708 .649 .555 .458 .273 |
.435 .435 .435 .435 .435 .435 |
.1250 .1934 .2346 .2913 .3421 .4110 |
1 1/2 |
1.900 |
. . Std xs . Xxs |
. . 40 80 160 . |
5s 10s 40s 80s . . |
.065 .109 .145 .200 .281 .400 |
1.770 1.682 1.610 1.500 1.338 1.100 |
.3747 .6133 .7995 1.068 1.429 1.885 |
2.461 2.222 2.036 1.767 1.406 .950 |
.01709 .01543 .01414 .01225 .00976 .00660 |
.1579 .2468 .3099 .3912 .4824 .5678 |
1.28 2.09 2.72 3.63 4.86 6.41 |
1.066 .963 .882 .765 .608 .42 |
.497 .497 .497 .497 .497 .497 |
.1662 .2598 .3262 .4118 .5078 .5977 |
2 |
2.375 |
. . Std xs . Xxs |
. . 40 80 160 . |
5s 10s 40s 80s . . |
.065 .109 .154 .218 .344 .436 |
2.245 2.157 2.067 1.939 1.687 1.503 |
.4717 .7760 1.075 1.477 2.190 2.656 |
3.958 3.654 3.355 2.953 2.241 1.774 |
.02749 .02538 .02330 .02050 .01556 .01232 |
.3149 .4992 .6657 .8679 1.162 1.311 |
1.61 2.64 3.65 5.02 7.46 9.03 |
1.72 1.58 1.45 1.28 .97 .77 |
.622 .622 .622 .622 .622 .622 |
.2652 .4204 .5606 .7309 .979 1.104 |
2 1/2 |
2.875 |
. . Std xs . Xxs |
. . 40 80 160 . |
5s 10s 40s 80s . . |
.083 .120 .203 .276 .375 .552 |
2.709 2.635 2.469 2.323 2.125 1.771 |
.7280 1.039 1.704 2.254 2.945 4.028 |
5.764 5.453 4.788 4.238 3.546 2.464 |
.04002 .03787 .03322 .02942 .02463 .01710 |
.7100 .9873 1.530 1.924 2.353 2.871 |
2.48 3.53 5.79 7.66 10.01 13.69 |
2.50 2.36 2.07 1.87 1.54 1.07 |
.753 .753 .753 .753 .753 .753 |
.4939 .6868 1.064 1.339 1.638 1.997 |
3 |
3.500 |
. . Std xs . Xxs |
. . 40 80 160 . |
5s 10s 40s 80s . . |
.083 .120 .216 .300 .438 .600 |
3.334 3.260 3.068 2.900 2.624 2.300 |
.8910 1.274 2.228 3.016 4.205 5.466 |
8.730 8.347 7.393 6.605 5.408 4.155 |
.06063 .05796 .05130 .04587 .03755 .02885 |
1.301 1.822 3.017 3.894 5.032 5.993 |
3.03 4.33 7.58 10.25 14.32 18.58 |
3.78 3.62 3.20 2.6 2.35 1.80 |
.916 .916 .916 .916 .916 .916 |
.7435 1.041 1.724 2.225 2.876 3.424 |
3 1/2 |
4.000 |
. . Std Xs |
. . 40 80 |
5s 10s 40s 80s |
.083 .120 .226 .318 |
3.834 3.760 3.548 3.364 |
1.021 1.463 2.680 3.678 |
11.545 11.104 9.886 8.888 |
.08017 .07711 .06870 .06170 |
1.960 2.755 4.788 6.280 |
3.48 4.97 9.11 12.50 |
5.00 4.81 4.29 3.84 |
1.047 1.047 1.047 1.047 |
.9799 1.378 2.394 3.140 |
4 |
4.500 |
. . Std xs . . Xxs |
. . 40 80 120 160 . |
5s 10s 40s 80s . . . |
.083 .120 .237 .337 .438 .531 .674 |
4.334 4.260 4.026 3.826 3.624 3.438 3.152 |
1.152 1.651 3.174 4.407 5.595 6.621 8.101 |
14.75 14.25 12.73 11.50 10.31 9.28 7.80 |
.10245 .09898 .08840 .07986 .0716 .0645 .0542 |
2.810 3.963 7.233 9.610 11.65 13.27 15.28 |
3.92 5.61 10.79 14.98 19.0 22.51 27.54 |
6.39 6.18 5.50 4.98 4.47 4.02 3.38 |
1.178 1.178 1.178 1.178 1.178 1.178 1.178 |
1.249 1.761 3.214 4.271 5.178 5.898 6.791 |
5 |
5.563 |
. . Std xs . . Xxs |
. . 40 80 120 160 . |
5s 10s 40s 80s . . . |
.109 .134 .258 .375 .500 .625 .750 |
5.345 5.295 5.047 4.813 4.563 4.313 4.063 |
1.868 2.285 4.300 6.112 7.953 9.696 11.340 |
22.44 22.02 20.01 18.19 16.35 14.61 12.97 |
.1558 .1529 .1390 .1263 .1136 .1015 .0901 |
6.947 8.425 15.16 20.67 25.73 30.03 33.63 |
6.36 7.77 14.62 20.78 27.04 32.96 38.55 |
9.72 9.54 8.67 7.88 7.09 6.33 5.61 |
1.456 1.456 1.456 1.456 1.456 1.456 1.456 |
2.498 3.029 5.451 7.431 9.250 10.796 12.090 |
6 |
6.625 |
. . Std xs . . Xxs |
. . 40 80 120 160 . |
5s 10s 40s 80s . . . |
.109 .134 .280 .432 .562 .718 .864 |
6.407 6.357 6.065 5.761 5.501 5.187 4.897 |
2.231 2.733 5.581 8.405 10.70 13.32 15.64 |
32.24 31.74 28.89 26.07 23.77 21.15 18.84 |
.2239 .2204 .2006 .1810 .1650 .1469 .1308 |
11.85 14.40 28.14 40.49 49.61 58.97 66.33 |
7.60 9.29 18.97 28.57 36.39 45.35 53.16 |
13.97 13.75 12.51 11.29 10.30 9.16 8.16 |
1.734 1.734 1.734 1.734 1.734 1.734 1.734 |
3.576 4.346 8.496 12.22 14.98 17.81 20.02 |
8 |
8.625 |
. . . . Std . Xs . . . Xxs . |
. . 20 30 40 60 80 100 120 140 . 160 |
5s 10s . . 40s . 80s . . . . . |
.109 .148 .250 .277 .322 .406 .500 .594 .719 .812 .875 .906 |
8.407 8.329 8.125 8.071 7.981 7.813 7.625 7.437 7.187 7.001 6.875 6.813 |
2.916 3.941 6.57 7.26 8.40 10.48 12.76 14.96 17.84 19.93 21.30 21.97 |
55.51 54.48 51.85 51.16 50.03 47.94 45.66 43.46 40.59 38.50 37.12 36.46 |
.3855 .3784 .3601 .3553 .3474 .3329 .3171 .3018 .2819 .2673 .2578 .2532 |
26.44 35.41 57.72 63.35 72.49 88.73 105.7 121.3 140.5 153.7 162.0 165.9 |
9.93 13.40 22.36 24.70 28.55 35.64 43.39 50.95 60.71 67.76 72.42 74.69 |
24.06 23.61 22.47 22.17 21.70 20.77 19.78 18.83 17.59 16.68 16.10 15.80 |
2.258 2.258 2.258 2.258 2.258 2.258 2.258 2.258 2.258 2.258 2.258 2.258 |
6.131 8.212 13.39 14.69 16.81 20.58 24.51 28.14 32.58 35.65 37.56 38.48 |
10 |
10.750 |
. . . . Std xs . . . . . |
. . 20 30 40 60 80 100 120 140 160 |
5s 10s . . 40s 80s . . . . . |
.134 .165 .250 .307 .365 .500 .594 .719 .844 1.000 1.125 |
10.482 10.420 10.250 10.136 10.020 9.750 9.562 9.312 9.062 8.750 8.500 |
4.36 5.49 8.24 10.07 11.90 16.10 18.92 22.63 26.24 30.63 34.02 |
86.29 85.28 82.52 80.69 78.86 74.66 71.84 68.13 64.53 60.13 56.75 |
.5992 .5922 .5731 .5603 .5475 .5185 .4989 .4732 .4481 .4176 .3941 |
63.0 76.9 113.7 137.4 160.7 212.0 244.8 286.1 324.2 367.8 399.3 |
15.19 18.65 28.04 34.24 40.48 54.74 64.43 77.03 89.29 104.13 115.64 |
37.39 36.95 35.76 34.96 34.20 32.35 31.13 29.53 27.96 26.06 24.59 |
2.814 2.814 2.814 2.814 2.814 2.814 2.814 2.814 2.814 2.814 2.814 |
11.71 14.30 21.15 25.57 29.90 39.43 45.54 53.22 60.32 68.43 74.29 |
12 |
12.75 |
. . . . Std . Xs . . . . . . |
. . 20 30 . 40 . 60 80 100 120 140 160 |
5s 10s . . 40s . 80s . . . . . . |
.156 .180 .250 .330 .375 .406 .500 .562 .688 .844 1.000 1.125 1.312 |
12.438 12.390 12.250 12.090 12.000 11.938 11.750 11.626 11.374 11.062 10.750 10.500 10.126 |
6.17 7.11 9.82 12.87 14.58 15.77 19.24 21.52 26.03 31.53 36.91 41.08 47.14 |
121.50 120.57 117.86 114.80 113.10 111.93 108.43 106.16 101.64 96.14 90.76 86.59 80.53 |
.8438 .8373 .8185 .7972 .7854 .7773 .7528 .7372 .7058 .6677 .6303 .6013 .5592 |
122.4 140.4 191.8 248.4 279.3 300.3 361.5 400.4 475.1 561.6 641.6 700.5 781.1 |
20.98 24.17 33.38 43.77 49.56 53.52 65.42 73.15 88.63 107.32 125.49 139.67 160.27 |
52.65 52.25 51.07 49.74 49.00 48.50 46.92 46.00 44.04 41.66 39.33 37.52 34.89 |
3.338 3.338 3.338 3.338 3.338 3.338 3.338 3.338 3.338 3.338 3.338 3.338 3.338 |
19.2 22.0 30.2 39.0 43.8 47.1 56.7 62.8 74.6 88.1 100.7 109.9 122.6 |
14 |
14.00 |
. . . . Std . Xs . . . . . .. |
. . 10 20 30 40 . 60 80 100 120 140 160 |
5s 10s . . . . . . . . . . . |
156 .188 .250 .312 .375 .438 .500 .594 .750 .938 1.094 1.250 1.406 |
13.688 13.624 13.500 13.376 13.250 13.124 13.000 12.812 12.500 12.124 11.812 11.500 11.188 |
6.78 8.16 10.80 13.42 16.05 18.66 21.21 24.98 31.22 38.45 44.32 50.07 55.63 |
147.15 145.78 143.14 140.52 137.88 135.28 132.73 128.96 122.72 115.49 109.62 103.87 98.31 |
1.0219 1.0124 .9940 .9758 .9575 .9394 .9217 .8956 .8522 .8020 .7612 .7213 .6827 |
162.6 194.6 255.3 314.4 372.8 429.1 483.8 562.3 678.3 824.4 929.6 1027.0 1117.0 |
23.07 27.73 36.71 45.61 54.57 63.44 72.09 85.05 106.13 130.85 150.79 170.28 189.11 |
63.77 63.17 62.03 60.89 59.75 58.64 57.46 55.86 53.18 50.04 47.45 45.01 42.60 |
3.665 3.665 3.665 3.665 3.665 3.665 3.665 3.665 3.665 3.665 3.665 3.665 3.665 |
23.2 27.8 36.6 45.0 53.2 61.3 69.1 80.3 98.2 117.8 132.8 146.8 159.6 |
16 |
16.00 |
. . . . Std xs . . . . . . |
. . 10 20 30 40 60 80 100 120 140 160 |
5s 10s . . . . . . . . . . |
.165 .188 .250 .312 .375 .500 .656 .844 1.031 1.219 1.438 1.594 |
15.670 15.624 15.500 15.376 15.250 15.000 14.688 14.312 13.938 13.562 13.124 12.812 |
8.21 9.34 12.37 15.38 18.41 24.35 31.62 40.14 48.48 56.56 65.78 72.10 |
192.85 191.72 188.69 185.69 182.65 176.72 169.44 160.92 152.58 144.50 135.28 128.96 |
1.3393 1.3314 1.3103 1.2895 1.2684 1.2272 1.1766 1.175 1.0596 1.0035 .9394 .8956 |
257.3 291.9 383.7 473.2 562.1 731.9 932.4 1155.8 1364.5 1555.8 1760.3 1893.5 |
27.90 31.75 42.05 52.27 62.58 82.77 107.50 136.61 164.82 192.43 223.64 245.25 |
83.57 83.08 81.74 80.50 79.12 76.58 73.42 69.73 66.12 62.62 58.64 55.83 |
4.189 4.189 4.189 4.189 4.189 4.189 4.189 4.189 4.189 4.189 4.189 4.189 |
32.2 36.5 48.0 59.2 70.3 91.5 116.6 144.5 170.5 194.5 220.0 236.7 |
18 |
18.00 |
. . . . Std . Xs . . . . . . . |
. . 10 20 . 30 . 40 60 80 100 120 140 160 |
5s 10s . . . . . . . . . . . . |
.165 .188 .250 .312 .375 .438 .500 .562 .750 .938 1.156 1.375 1.562 1.781 |
17.670 17.624 17.500 17.376 17.250 17.124 17.000 16.876 16.500 16.124 15.688 15.250 14.876 14.438 |
9.25 10.52 13.94 17.34 20.76 24.17 27.49 30.79 40.64 50.23 61.17 71.81 80.66 90.75 |
245.22 243.95 240.53 237.13 233.71 230.30 226.98 223.68 213.83 204.24 193.30 182.66 173.80 163.72 |
1.7029 1.6941 1.6703 1.6467 1.6230 1.5990 1.5763 1.5533 1.4849 1.4183 1.3423 1.2684 1.2070 1.1369 |
367.6 417.3 549.1 678.2 806.7 930.3 1053.2 1171.5 1514.7 1833.0 2180.0 2498.1 2749.0 3020.0 |
31.43 35.76 47.39 58.94 70.59 82.15 93.45 104.67 138.17 170.92 207.96 244.14 274.22 308.50 |
106.26 105.71 104.21 102.77 101.18 99.84 98.27 96.93 92.57 88.50 83.76 79.07 75.32 70.88 |
4.712 4.712 4.712 4.712 4.712 4.712 4.712 4.712 4.712 4.712 4.712 4.712 4.712 4.712 |
40.8 46.4 61.1 75.5 89.6 103.4 117.0 130.1 168.3 203.8 242.3 277.6 305.5 335.6 |
20 |
20.00 |
. . . Std xs . . . . . . . |
. . 10 20 30 40 60 80 100 120 140 160 |
5s 10s . . . . . . . . . . |
.188 .218 .250 .375 .500 .594 .812 1.031 1.281 1.500 1.750 1.969 |
19.624 19.564 19.500 19.250 19.000 18.812 18.376 17.938 17.438 17.000 16.500 16.062 |
11.70 13.55 15.51 23.12 30.63 36.15 48.95 61.44 75.33 87.18 100.33 111.49 |
302.46 300.61 298.65 290.04 283.53 278.00 265.21 252.72 238.83 226.98 213.82 202.67 |
2.1004 2.0876 2.0740 2.0142 1.9690 1.9305 1.8417 1.7550 1.6585 1.5762 1.4849 1.4074 |
574.2 662.8 765.4 1113.0 1457.0 1703.0 2257.0 2772.0 3315.2 3754.0 4216.0 4585.5 |
39.78 46.06 52.73 78.60 104.13 123.11 166.40 208.87 256.10 296.37 341.09 379.17 |
131.06 130.27 129.42 125.67 122.87 120.46 114.92 109.51 103.39 98.35 92.66 87.74 |
5.236 5.236 5.236 5.236 5.236 5.236 5.236 5.236 5.236 5.236 5.236 5.236 |
57.4 66.3 75.6 111.3 145.7 170.4 225.7 277.1 331.5 375.5 421.7 458.5 |
22 |
22.00 |
. . . Std xs . . . . . . |
. . 10 20 30 60 80 100 120 140 160 |
5s 10s . . . . . . . . . |
.188 .218 .250 .375 .500 .875 1.125 1.375 1.625 1.875 2.125 |
21.624 21.564 21.500 21.250 21.000 20.250 19.75 19.25 18.75 18.25 17.75 |
12.88 14.92 17.08 25.48 33.77 58.07 73.78 89.09 104.02 118.55 132.68 |
367.25 365.21 363.05 354.66 346.36 322.06 306.35 291.04 276.12 261.59 247.45 |
2.5503 2.5362 2.5212 2.4629 2.4053 2.2365 2.1275 2.0211 1.9175 1.8166 1.71840 |
766.2 884.8 1010.3 1489.7 1952.5 3244.9 4030.4 4758.5 5432.0 6053.7 6626.4 |
43.80 50.71 58.07 86.61 114.81 197.41 250.81 302.88 353.61 403.00 451.06 |
159.14 158.26 157.32 153.68 150.09 139.56 132.76 126.12 119.65 113.36 107.23 |
5.760 5.760 5.760 5.760 5.760 5.760 5.760 5.760 5.760 5.760 5.760 |
69.7 80.4 91.8 135.4 117.5 295.0 366.4 432.6 493.8 550.3 602.4 |
24 |
24.00 |
. . Std xs . . . . . . . . |
. 10 20 . 30 40 60 80 100 120 140 160 |
5s 10s . . . . . . . . . . |
.218 .250 .375 .500 .562 .688 .969 1.219 1.531 1.812 2.062 2.344 |
23.564 23.500 23.250 23.000 22.876 22.624 22.062 21.562 20.938 20.376 19.876 19.312 |
16.29 18.65 27.83 36.91 41.39 50.31 70.04 87.17 108.07 126.31 142.11 159.41 |
436.10 433.74 424.56 415.48 411.00 402.07 382.35 365.22 344.32 326.08 310.28 292.98 |
3.0285 3.0121 2.9483 2.8853 2.8542 2.7921 2.6552 2.5362 2.3911 2.2645 2.1547 2.0346 |
1151.6 1315.4 1942.0 2549.5 2843.0 3421.3 4652.8 5672.0 6849.9 7825.0 8625.0 9455.9 |
55.37 63.41 94.62 125.49 140.68 171.29 238.35 296.58 367.39 429.39 483.12 542.13 |
188.98 187.95 183.95 179.87 178.09 174.23 165.52 158.26 149.06 141.17 134.45 126.84 |
6.283 6.283 6.283 6.283 6.283 6.283 6.283 6.283 6.283 6.283 6.283 6.283 |
96.0 109.6 161.9 212.5 237.0 285.1 387.7 472.8 570.8 652.1 718.9 787.9 |
26 |
26.00 |
. Std Xs |
10 . 20 |
. . . |
.312 .375 .500 |
25.376 25.250 25.000 |
25.18 30.19 40.06 |
505.75 500.74 490.87 |
3.5122 3.4774 3.4088 |
2077.2 2478.4 3257.0 |
85.60 102.63 136.17 |
219.16 216.99 212.71 |
6.806 6.806 6.806 |
159.8 190.6 250.5 |
28 |
28.00 |
. Std xs . |
10 . 20 30 |
. . . . |
.312 .375 .500 .625 |
27.376 27.250 27.000 26.750 |
27.14 32.54 43.20 53.75 |
588.61 583.21 572.56 562.00 |
4.0876 4.0501 3.9761 3.9028 |
2601.0 3105.1 4084.8 5037.7 |
92.26 110.64 146.85 182.73 |
255.07 252.73 248.11 243.53 |
7.330 7.330 7.330 7.330 |
185.8 221.8 291.8 359.8 |
30 |
30.00 |
. . Std xs . |
. 10 . 20 30 |
5s 10s . . . |
.250 .312 .375 .500 .625 |
29.500 29.376 29.250 29.000 28.750 |
23.37 29.10 34.90 46.34 57.68 |
683.49 677.76 671.96 660.52 649.18 |
4.7465 4.7067 4.6664 4.5869 4.5082 |
2585.2 3206.3 3829.4 5042.2 6224.0 |
79.43 98.93 118.65 157.53 196.08 |
296.18 293.70 291.18 286.22 281.31 |
7.854 7.854 7.854 7.854 7.854 |
172.3 213.8 255.3 336.1 414.9 |
32 |
32.00 |
. Std xs . . |
10 . 20 30 40 |
. . . . . |
.312 .375 .500 .625 .688 |
31.376 31.250 31.000 30.750 30.624 |
31.06 37.26 49.48 61.60 67.68 |
773.19 766.99 754.77 742.64 736.57 |
5.3694 5.3263 5.2414 5.1572 5.1151 |
3898.9 4658.5 6138.6 7583.4 8298.3 |
105.59 126.66 168.21 209.43 230.08 |
335.05 332.36 327.06 321.81 319.18 |
8.378 8.378 8.378 8.378 8.378 |
243.7 291.2 383.7 474.0 518.6 |
34 |
34.00 |
. Std xs . . |
10 . 20 30 40 |
. . . . . |
.344 .375 .500 .625 .688 |
33.312 33.250 33.000 32.750 32.624 |
36.37 39.61 52.62 65.53 72.00 |
871.55 868.31 855.30 842.39 835.92 |
6.0524 6.0299 5.9396 5.8499 5.8050 |
5150.5 5599.3 7383.5 9127.6 9991.6 |
123.65 134.67 178.89 222.78 244.77 |
377.67 376.27 370.63 365.03 362.23 |
8.901 8.901 8.901 8.901 8.901 |
303.0 329.4 434.3 536.9 587.7 |
36 |
36.00 |
. Std xs . . |
10 . 20 30 40 |
. . . . . |
.312 .375 .500 .625 .750 |
35.376 35.250 35.000 34.750 34.500 |
34.98 41.97 55.76 69.46 83.06 |
982.90 975.91 962.11 948.42 934.82 |
6.8257 6.7771 6.6813 6.5862 6.4918 |
5569.5 6658.9 8786.2 10868.4 12906.1 |
118.92 142.68 189.57 236.13 282.35 |
425.92 422.89 416.91 417.22 405.09 |
9.425 9.425 9.425 9.425 9.425 |
309.4 369.9 488.1 603.8 717.0 |
42 |
42.00 |
Std xs . . |
. 20 30 40 |
. . . . |
.375 .500 .625 .750 |
41.250 41.000 40.720 40.500 |
49.08 65.18 81.28 97.23 |
1336.3 1320.2 1304.1 1288.2 |
. . . . |
10627 14037 17373 20689 |
167 222 276 330 |
579.3 572.3 565.4 558.4 |
10.99 10.99 10.99 10.99 |
506.1 668.4 827.3 985.2 |
Sch |
Sch-5/5s |
Sch-10/10s |
Sch-40/40s |
Sch-80/80s |
Sch-100 |
Sch-120 |
Sch-160 |
Sch-xxs |
|
Pressure |
7 kg Cm2 |
10 kg Cm2 |
32 kg cm2 |
79 kg cm2 |
110 kg Cm2 |
160 kg Cm2 |
350 kg Cm2 |
675 kg/cm2 |
|
Pressure hold at 15 min |
Grade | Uns no | Composition, %b | |||||||||||||||||
Carbon | Manganese | Phosphorus | Sulfur | Silicon | Chrom- ium | Nickel | Molyb- denum | Titanium | Niobiumm | Tanta- lum, max | Nitro- genc | Vana- dium | Copper | Cerium | Boron | Aluminum | Other | ||
Tp201 | S20100 | 0.15 | 5.5– | 0.060 | 0.030 | 1.00 | 16.0– | 3.5– | . . . | . . . | . . . | . . . | 0.25 | . . . | . . . | . . . | . . . | . . . | |
7.5 | 18.0 | 5.5 | |||||||||||||||||
Tp201ln | S20153 | 0.03 | 6.4– | 0.045 | 0.015 | 0.75 | 16.0– | 4.0– | . . . | . . . | . . . | . . . | 0.10– | . . . | 1.00 | . . . | . . . | . . . | |
7.5 | 17.5 | 5.0 | 0.25 | ||||||||||||||||
. . . | S20400 | 0.030 | 7.0– | 0.045 | 0.030 | 1.00 | 15.0– | 1.50– | . . . | . . . | . . . | . . . | 0.15– | . . . | . . . | . . . | . . . | . . . | |
9.0 | 17.0 | 3.00 | 0.30 | ||||||||||||||||
Tpxm-19 | S20910 | 0.06 | 4.0– | 0.045 | 0.030 | 1.00 | 20.5– | 11.5– | 1.50– | . . . | 0.10– | . . . | 0.20– | 0.10– | . . . | . . . | |||
6.0 | 23.5 | 13.5 | 3.00 | 0.30 | 0.40 | 0.30 | |||||||||||||
Tpxm-10 | S21900 | 0.08 | 8.0– | 0.045 | 0.030 | 1.00 | 19.0– | 5.5– | . . . | . . . | . . . | . . . | 0.15– | . . . | . . . | . . . | |||
10.0 | 21.5 | 7.5 | 0.40 | ||||||||||||||||
Tpxm-11 | S21904 | 0.04 | 8.0– | 0.045 | 0.030 | 1.00 | 19.0– | 5.5– | . . . | . . . | . . . | . . . | 0.15– | . . . | . . . | . . . | |||
10.0 | 21.5 | 7.5 | 0.40 | ||||||||||||||||
Tpxm-29 | S24000 | 0.08 | 11.5– | 0.060 | 0.030 | 1.00 | 17.0– | 2.3– | . . . | . . . | . . . | . . . | 0.20– | . . . | . . . | . . . | |||
14.5 | 19.0 | 3.7 | 0.40 | ||||||||||||||||
Tp304 | S30400 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0– | 8.0– | . . . | . . . | . . . | . . . | . . . | . . . | . . . | . . . | |||
20.0 | 11.0 | ||||||||||||||||||
Tp304l | S30403 | 0.035d | 2.00 | 0.045 | 0.030 | 1.00 | 18.0– | 8.0– | . . . | . . . | . . . | . . . | . . . | . . . | . . . | . . . | |||
20.0 | 13.0 | ||||||||||||||||||
Tp304h | S30409 | 0.04– | 2.00 | 0.045 | 0.030 | 1.00 | 18.0– | 8.0– | . . . | . . . | . . . | . . . | . . . | . . . | . . . | . . . | |||
0.10 | 20.0 | 11.0 | |||||||||||||||||
. . . | S30415 | 0.04– | 0.80 | 0.045 | 0.030 | 1.00– | 18.0– | 9.0– | . . . | . . . | . . . | . . . | 0.12– | . . . | . . . | 0.03– | |||
0.06 | 2.00 | 19.0 | 10.0 | 0.18 | 0.08 | ||||||||||||||
Tp304n | S30451 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0– | 8.0– | . . . | . . . | . . . | . . . | 0.10– | . . . | . . . | . . . | |||
20.0 | 11.0 | 0.16 | |||||||||||||||||
Tp304ln | S30453 | 0.035 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0– | 8.0– | . . . | . . . | . . . | . . . | 0.10– | . . . | . . . | . . . | |||
20.0 | 12.0 | 0.16 | |||||||||||||||||
. . . | S30600 | 0.018 | 2.00 | 0.02 | 0.02 | 3.7– | 17.0– | 14.0– | 0.20 | . . . | . . . | . . . | . . . | . . . | 0.50 | . . . | |||
4.3 | 18.5 | 15.5 | Max | ||||||||||||||||
. . . | S30601 | 0.015 | 0.50– | 0.030 | 0.013 | 5.0– | 17.0– | 17.0– | 0.20 | . . . | . . . | . . . | 0.05 | . . . | 0.35 | . . . | . . . | . . . | . . . |
0.80 | 5.6 | 18.0 | 18.0 | ||||||||||||||||
. . . | S30615 | 0.16– | 2.00 | 0.030 | 0.03 | 3.2– | 17.0– | 13.5– | . . . | . . . | . . . | . . . | . . . | . . . | . . . | . . . | . . . | 0.80– | |
0.24 | 4.0 | 19.5 | 16.0 | 1.50 | |||||||||||||||
. . . | S30815 | 0.05– | 0.80 | 0.040 | 0.030 | 1.40– | 20.0– | 10.0– | . . . | . . . | . . . | . . . | 0.14– | . . . | . . . | 0.03– | |||
0.10 | 2.00 | 22.0 | 12.0 | 0.20 | 0.08 | ||||||||||||||
Tp309s | S30908 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 22.0– | 12.0– | 0.75 | . . . | . . . | . . . | . . . | . . . | . . . | ||||
24.0 | 15.0 | ||||||||||||||||||
Tp309h | S30909 | 0.04– | 2.00 | 0.045 | 0.030 | 1.00 | 22.0– | 12.0– | . . . | . . . | . . . | . . . | . . . | . . . | . . . | ||||
0.10 | 24.0 | 15.0 | |||||||||||||||||
Tp309cb | S30940 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 22.0– | 12.0– | 0.75 | . . . | 10 × c | . . . | . . . | . . . | . . . | ||||
24.0 | 16.0 | Min, | |||||||||||||||||
1.10 max | |||||||||||||||||||
Tp309hcb | S30941 | 0.04– | 2.00 | 0.045 | 0.030 | 1.00 | 22.0– | 12.0– | 0.75 | . . . | 10 × c | . . . | . . . | . . . | |||||
0.10 | 24.0 | 16.0 | Min, | ||||||||||||||||
1.10 max | |||||||||||||||||||
S31002 | 0.015 | 2.00 | 0.020 | 0.015 | 0.15 | 24.0– | 19.0– | 0.10 | . . . | . . . | . . . | 0.10 | . . . | ||||||
26.0 | 22.0 | ||||||||||||||||||
Tp310s | S31008 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 24.0– | 19.0– | 0.75 | . . . | . . . | . . . | . . . | . . . | . . . | ||||
26.0 | 22.0 | ||||||||||||||||||
Tp310h | S31009 | 0.04– | 2.00 | 0.045 | 0.030 | 1.00 | 24.0– | 19.0– | . . . | . . . | . . . | . . . | . . . | . . . | . . . | ||||
0.10 | 26.0 | 22.0 | |||||||||||||||||
S31035 | 0.04– | 0.60 | 0.025 | 0.015 | 0.40 | 21.5– | 23.5– | 0.40– | 0.20– | 2.5– | 0.002– | W 3.0– | |||||||
0.10 | 23.5 | 26.5 | 0.60 | 0.30 | 3.5 | 0.008 | 4.0 | ||||||||||||
Co 1.0– | |||||||||||||||||||
2.0 | |||||||||||||||||||
Tp310cb | S31040 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 24.0– | 19.0– | 0.75 | . . . | 10 × c | . . . | . . . | . . . | . . . | ||||
26.0 | 22.0 | Min, | |||||||||||||||||
1.10 max | |||||||||||||||||||
Tp310hcb | S31041 | 0.04– | 2.00 | 0.045 | 0.030 | 1.00 | 24.0– | 19.0– | 0.75 | . . . | 10 × c | . . . | . . . | . . . | |||||
0.10 | 26.0 | 22.0 | Min, | ||||||||||||||||
1.10 max | |||||||||||||||||||
. . . | S31050 | 0.025 | 2.00 | 0.020 | 0.015 | 0.4 | 24.0– | 20.5– | 1.6– | . . . | . . . | . . . | 0.09– | . . . | . . . | . . . | |||
26.0 | 23.5 | 2.6 | 0.15 | ||||||||||||||||
. . . | S31254 | 0.020 | 1.00 | 0.030 | 0.010 | 0.80 | 19.5– | 17.5– | 6.0– | . . . | . . . | . . . | 0.18– | . . . | 0.50– | . . . | |||
20.5 | 18.5 | 6.5 | 0.25 | 1.00 | |||||||||||||||
. . . | S31266 | 0.030 | 2.00– | 0.035 | 0.020 | 1.00 | 23.0– | 21.0– | 5.2– | 0.35– | 1.00– | W 1.50– | |||||||
4.00 | 25.0 | 24.0 | 6.2 | 0.60 | 2.50 | 2.50 | |||||||||||||
S31272 | 0.08– | 1.5– | 0.030 | 0.015 | 0.25– | 14.0– | 14.0– | 1.00– | 0.30– | 0.004– | |||||||||
012 | 2.00 | 0.75 | 16.0 | 16.0 | 1.40 | 0.60 | 0.008 | ||||||||||||
S31277 | 0.020 | 3.00 | 0.030 | 0.010 | 0.50 | 20.5– | 26.0– | 6.5– | 0.30– | 0.50– | |||||||||
23.0 | 28.0 | 8.0 | 0.40 | 1.50 | |||||||||||||||
Tp316 | S31600 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 16.0– | 10.0– | 2.00– | . . . | . . . | . . . | . . . | . . . | . . . | . . . | |||
18.0 | 14.0 | 3.00 | |||||||||||||||||
Tp316l | S31603 | 0.035d | 2.00 | 0.045 | 0.030 | 1.00 | 16.0– | 10.0– | 2.00– | . . . | . . . | . . . | . . . | . . . | . . . | . . . | |||
18.0 | 14.0 | 3.00 | |||||||||||||||||
Tp316h | S31609 | 0.04– | 2.00 | 0.045 | 0.030 | 1.00 | 16.0– | 10.0– | 2.00– | . . . | . . . | . . . | . . . | . . . | . . . | . . . | |||
0.10 | 18.0 | 14.0 | 3.00 | ||||||||||||||||
Tp316ti | S31635 | 0.08 | 2.00 | 0.045 | 0.030 | 0.75 | 16.0– | 10.0– | 2.00– | 5× | . . . | . . . | 0.10 | . . . | . . . | . . . | . . . | . . . | |
18.0 | 14.0 | 3.00 | (c+n) | ||||||||||||||||
–0.70 | |||||||||||||||||||
Tp316n | S31651 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 16.0– | 10.0– | 2.00– | 0.10– | . . . | . . . | . . . | ||||||
18.0 | 14.0 | 3.00 | 0.16 | ||||||||||||||||
Tp316ln | S31653 | 0.035 | 2.00 | 0.045 | 0.030 | 1.00 | 16.0– | 10.0– | 2.00– | . . . | . . . | . . . | 0.10– | . . . | . . . | . . . | |||
18.0 | 14.0 | 3.00 | 0.16 | ||||||||||||||||
. . . | S31655 | 0.030 | 2.00 | 0.045 | 0.015 | 1.00 | 19.5– | 8.0– | 0.50– | . . . | . . . | . . . | 0.14– | . . . | 1.00 | . . . | . . . | . . . | . . . |
21.5 | 9.5 | 1.50 | 0.25 | ||||||||||||||||
Tp317 | S31700 | 0.08 | 2.00 | 0.045 | 0.030 | 1.00 | 18.0– | 11.0– | 3.0– | . . . | . . . | . . . | . . . | . . . | . . . | . . . | |||
20.0 | 15.0 | 4.0 |